Responded to unit 111 for air conditioning evaluation and documented frozen evaporator coil condition causing water drainage issues into the unit below. Photographed damaged HVAC equipment panel and exterior condensate drain line area with accumulated debris, scheduling return visit to address frozen coil repair and restore proper system operation.

Replaced plastic water supply fittings with code-compliant metal fittings in exposed ceiling area as required by building inspector. The work involved the hot and cold water supply lines (identified by red and blue PEX tubing) running through the ceiling joists, where plastic compression fittings were removed and replaced with brass or copper transition fittings. All connections were properly secured to the wooden framing members using appropriate mounting hardware. Photographed completed installation showing the metal fittings installed at junction points, electrical box location noted for clearance purposes, and overall condition of the work area. All replaced fittings now meet current plumbing code requirements for inspection approval.

Completed planned HVAC membership air conditioning maintenance service. Inspected outdoor disconnect box and electrical connections, finding aged wiring with minor discoloration on terminal blocks but all connections secure and operational. System components functioning within normal parameters.

Replaced failed 40/5 MFD dual run capacitor on air conditioning unit to restore proper operation of compressor and condenser fan motor. Installed hard start kit (compressor start assist) to reduce inrush current and extend compressor lifespan, particularly beneficial for aging compressor experiencing difficulty on startup. All electrical connections verified secure, system tested and confirmed operating within normal parameters.

Responded to no cooling complaint on Lennox air conditioning system. Upon arrival, found outdoor condenser unit operational but not providing adequate cooling to structure. Performed diagnostic assessment of refrigerant levels, electrical connections, and compressor function to identify root cause of insufficient cooling performance.

Completed scheduled air conditioning maintenance per membership agreement. Performed comprehensive system inspection of outdoor heat pump unit, including evaluation of capacitor, electrical connections, and refrigerant lines. All components found operating within normal parameters with minor cosmetic corrosion noted on copper tubing consistent with typical outdoor exposure.

Completed routine air conditioning tune-up and preventative maintenance on 20+ year old system. Performed comprehensive system evaluation including temperature differential testing, electrical measurements, and component inspection per standard checklist protocol. Recorded indoor temperature at 70°F, supply air temperature at 58°F, and outdoor ambient at 70°F. Verified proper operation of condensing unit with compressor amp draw measured at 16.5A. Tested capacitor functionality showing 50µF reading within acceptable range. Confirmed electrical supply voltages at disconnect and contactor showing 245V line voltage and 121.5V control voltage, all within normal operating parameters. Cleaned evaporator coil and inspected condensate drain system with proper drainage confirmed. Evaluated blower motor operation and airflow across evaporator coil. Inspected contactors and control board for signs of wear or damage with no issues found. System operating normally with no deficiencies noted at time

Completed planned air conditioning maintenance as part of membership service. Performed system inspection with access to electrical and mechanical components, including capacitors, compressor, and wiring connections. Customer requests filter replacement (#80 canister) to be scheduled for fall service.

Completed planned maintenance on outdoor air conditioning unit. Upon inspection, found condenser coil heavily clogged with dirt, dust, and debris accumulation, significantly restricting airflow. Cleaned condenser coil thoroughly to restore proper heat transfer efficiency. Inspected electrical compartment components including capacitor, contactor, and wiring connections—all found in operational condition with secure connections and proper grounding. System returned to normal operating parameters following maintenance procedures.

Completed planned maintenance inspection on outdoor air conditioning unit as part of recurring HVAC membership service. Accessed electrical compartment and inspected all major components including Genteq capacitor, contactor relay, wiring connections, and compressor motor. Unit interior showed significant accumulation of dirt, debris, cobwebs, and organic matter throughout compartment, indicating extended operation without recent maintenance. All electrical connections, capacitor, and contactor were visually inspected and found to be functional despite heavy soiling conditions.

Responded to no cooling complaint at commercial medical facility with complete loss of airflow to surgical area. Performed diagnostic evaluation on newer HVAC system and measured temperature readings at equipment using calibrated digital instrumentation. System found to be non-operational with no air delivery through ductwork and no tripped breakers reported.

Completed planned maintenance service on residential cooling system. Performed comprehensive inspection of outdoor condenser unit, verified proper electrical connections and capacitor operation, checked refrigerant levels, and confirmed all mechanical components functioning within normal parameters. Unit operating efficiently with no deficiencies noted at time of service.

# HVAC Membership - A/C Maintenance Completed Performed comprehensive planned maintenance service on residential air conditioning system. Conducted thorough inspection of outdoor condenser unit, including examination of electrical components, control boards, and wiring connections. Accessed internal control panel to verify proper operation of electronic controls and circuit boards. Inspected copper inductive coils, capacitors, and integrated circuits for signs of wear or damage. Verified all wire connections and harnesses were secure and properly routed. Checked condenser unit mounting on concrete pad and confirmed adequate drainage around equipment. Examined refrigerant line connections, electrical disconnect box, and PVC conduit installations. Documented equipment condition through photographic records. All components found operating within normal parameters. Unit ready for continued service.

Completed emergency plumbing repairs in women's restroom during scheduled water shut-off. Rebuilt urinal assembly and replaced defective shut-off valve for toilet fixture, restoring full functionality to both fixtures.

Responded to master bathroom toilet with continuous running condition and broken flush handle. Upon inspection, removed tank lid and identified worn flapper assembly and failed flush lever mechanism. Tank water showed significant mineral deposits and discoloration indicating age and hard water conditions. Replaced defective flush valve assembly including flapper seal and overflow tube. Installed new chrome flush handle and linkage assembly to restore proper manual operation. Adjusted fill valve and water level to manufacturer specifications. Tested flush cycle multiple times to verify proper tank refill, complete bowl evacuation, and elimination of continuous running. Confirmed all components sealed properly with no leaks detected. Toilet restored to full operational status.

Installed new A.O. Smith standard residential tanked water heater in accordance with quoted specifications. Unit was properly positioned, connected to existing water supply and discharge lines, and secured in utility area. Installation completed with all connections tested and system verified operational.

Completed comprehensive cooling season tune-up on 9-year-old residential air conditioning system. Performed visual inspection of outdoor condenser unit, noting significant accumulation of dirt, dust, and debris on condenser coils and protective wire guard. Opened electrical control panel and inspected internal components including dual-run capacitor, contactor relay, and associated wiring connections for proper operation and signs of wear. Cleaned condenser coils and removed organic debris from unit exterior to restore optimal airflow and heat transfer efficiency. Verified system operational status and confirmed unit cycling properly with no performance issues reported by customer.

Completed full HVAC system installation in new construction property, including ductwork rough-in throughout basement and main floor areas. Installed metal supply and return ducts with proper sizing and routing through framed walls and ceiling joists, ensuring adequate airflow distribution to all planned living spaces. System is ready for equipment connection and final commissioning once interior finishes are completed.

Completed planned air conditioning maintenance per membership agreement. Performed comprehensive system inspection of outdoor condensing unit, including visual examination of electrical components, capacitor, contactor assembly, and wiring connections. All electrical components found to be in proper working condition with secure wire connections and no signs of electrical failure. Noted standard wear consistent with normal operation. System operational and ready for cooling season.

Responded to no-cooling call on residential HVAC system approximately 10 years old. Upon arrival, confirmed system was clicking but failing to start with no airflow through vents and no tripped breakers. Performed diagnostic evaluation of electrical components at disconnect switch and main panel, inspected furnace unit and associated condensate lines, and examined all visible electrical connections and control circuits to identify failure point preventing compressor and blower operation.