Completed scheduled air conditioning maintenance as part of HVAC membership plan. Performed comprehensive system inspection including electrical components, contactor relay, and capacitor, all of which were found to be in functional condition. Removed minor debris from outdoor unit and documented equipment condition with photos for service records.

Responded to call for exterior wall leak occurring only when front yard hose spigot was operated. Conducted diagnostic inspection of outdoor spigot assembly and traced water intrusion path. Investigation revealed leak originating from failed connection or damaged pipe behind exterior wall penetration at spigot mounting location. Inspected attic space above affected area to assess potential water damage to insulation and structural components. Documented existing water staining on fiberglass insulation between roof rafters, indicating previous or ongoing moisture intrusion. Examined garden bed area surrounding exterior spigot foundation to identify soil saturation patterns and confirm leak source at wall penetration point. Photographed conditions in attic crawl space showing discolored insulation near HVAC ductwork and exterior landscaping area adjacent to siding where spigot is mounted. Provided assessment findings and repair recommendations to address failed plumbing connection at hos

Completed planned dual-system air conditioning maintenance on two residential condensing units positioned side-by-side at exterior location. Performed comprehensive preventive maintenance procedures including inspection of electrical components, capacitors, contactors, and wiring connections within control panels, cleaned condenser coils, checked refrigerant levels using manifold gauges, and replaced two 16x25x1 air filters per maintenance protocol.

Completed kitchen faucet replacement in 1950s-era home with customer-supplied fixture. Removed existing faucet assembly, installed new brushed stainless steel pull-down model with dual handles and verified all supply line connections beneath sink for proper operation. Tested hot and cold water flow, checked P-trap and drainage system for leaks, and confirmed no issues with existing plumbing infrastructure.

Picked up and installed ML14XC1-048-233 evaporator coil from Mid-City supply house. Removed existing furnace, installed new evaporator coil, and reinstalled Carrier furnace unit in utility closet. Connected refrigerant lines, condensate drainage system, and verified proper airflow through ductwork. System tested and operational with thermostat reading 68°F.

Completed plumbing installation work for Building 2 fire restoration project in a confined utility space beneath staircase area. Installed new white PVC piping system along floor level to replace fire-damaged lines, working around existing wall penetrations and structural framework while addressing significant water damage, rust staining, and mold contamination present throughout the space.

Completed installation of Lennox ML17KC2-036 air conditioning condenser unit and CK40CT-30B coil at residential property. Positioned outdoor condenser on plastic pad against exterior wall with proper clearances, connected refrigerant lines with insulated line set, and established electrical connections to existing disconnect. Reused existing thermostat and verified system operation upon startup. All components tested and confirmed operational per manufacturer specifications.

Responded to service call for refrigerant leak at indoor evaporator coil. Successfully located and repaired leak, then replaced line filter-drier to ensure system cleanliness and prevent future compressor damage. Performed nitrogen pressure test to verify leak repair integrity, evacuated system to proper vacuum levels, and recharged unit to manufacturer specifications. System tested and confirmed operational with proper pressures and temperatures upon completion.

Completed monthly Gold Level maintenance on single-system HVAC unit. Performed comprehensive inspection of outdoor condensing unit and electrical components, including capacitor, contactor, and wiring connections. All electrical connections verified secure, capacitor tested within normal operating parameters, and unit found operating properly with no deficiencies noted.

Temporarily removed furnace, coil, and ductwork to facilitate water remediation work by restoration contractor. Pumped refrigerant into outdoor unit and valved off system, recovered remaining refrigerant, disconnected and capped gas and refrigerant lines in basement, then removed return drop and plenum to within 6 inches of ceiling. All equipment and ductwork stored on-site for future reinstallation.

Responded to no-cool complaint with outdoor unit not running and warm air from vents. Upon arrival, found white cylindrical condenser unit positioned against exterior brick wall with airflow present at indoor registers and no ice buildup at evaporator coil. Performed visual inspection of outdoor unit, verified electrical disconnect box and refrigerant line connections, and documented condenser placement and surrounding installation components including PVC condensate drain and refrigerant line routing along foundation. System age unknown but reported as potentially under 10 years old.

Completed full installation of Lennox ML13KC1-036 air conditioning system with CK40UT-36C air handler and T4 thermostat at residential property. Mounted air handler vertically in basement mechanical room with proper clearances and secured to structural framing. Installed refrigerant line set with copper tubing, connecting outdoor condensing unit to indoor air handler with proper insulation and routing through building envelope. Positioned outdoor condenser unit on concrete pad in backyard area with level placement and adequate clearance for airflow and service access. Completed all electrical connections including power supply wiring, line voltage, and low voltage control wiring from main electrical panel to air handler and outdoor unit. Installed electrical disconnect box on exterior wall per code requirements for outdoor unit. Ran and terminated thermostat control wiring from air handler to T4 thermostat location. Installed PVC condensate drain line from air handler with proper pitc

Provided estimate for temporary removal and reinstallation of existing furnace system to facilitate water damage remediation work in basement area. Documented current HVAC equipment configuration including outdoor Goodman condenser unit and basement furnace installation with associated electrical connections, refrigerant lines, and utility routing through floor joists. Quote covers disconnection of all electrical and mechanical connections, safe removal of furnace unit from work area, protection of equipment during remediation process, and complete reinstallation with reconnection of all systems upon completion of water damage repairs.

Responded to emergency flooding situation in basement caused by failed sump pump system. Upon arrival, found approximately 1 inch of standing water covering 15-foot radius around sump pit. Assessed existing sump pump installation, documented wet concrete floor conditions and active water infiltration around corroded metal pit cover. Photographed complete system including vertical PVC discharge piping with mounting straps, electrical connections, and moisture barrier installation on surrounding walls.

Responded to no-water emergency at 35-year-old residence following recent storms. Upon arrival, confirmed complete loss of water supply throughout home affecting all fixtures and toilets. Investigated well system components in basement utility area, inspecting pressure tank, pressure switch, electrical connections, and control wiring. Found pressure switch contacts required attention and verified proper electrical supply to well pump contactor. Restored water service to full system functionality with all fixtures and toilets operating normally. Additionally performed scheduled preventive maintenance on 2-year-old air conditioning system. Completed standard tune-up procedures including inspection of electrical connections, refrigerant pressures, condenser coil condition, and overall system operation. Unit found in good working order with no deficiencies noted. System operating within manufacturer specifications.

Completed full HVAC system installation featuring a Lennox ML13KC1-024 condensing unit paired with a CK40DT-30/36B evaporator coil and compatible furnace. Removed and reinstalled existing furnace to accommodate proper coil placement, adding a 3-inch spacer beneath the evaporator coil to ensure adequate gravity drainage and prevent condensate backup. System tested and verified operational with all components functioning within manufacturer specifications.

Completed installation of tanked water heater in unfinished basement area with new plumbing connections, including copper supply lines with ball valve shut-off controls and PEX tubing integration. All connections were secured to wall framing with proper mounting brackets, system tested and verified operational, with final balance collected upon completion.

Replaced sump pump and check valve in far left corner of basement, cleaned sump pit to remove debris and sediment buildup, and installed check valve on perimeter drain discharge line. All components were properly secured with appropriate mounting hardware, electrical connections were verified, and the system was tested for proper operation and drainage flow.

Completed installation of Lennox ML13KC1-024 air conditioning system with CK40UT-24B-71 coil and T4 thermostat. System installed in residential basement utility room, connected to existing furnace infrastructure with proper refrigerant lines and electrical connections, verified all components operational and collected outstanding balance upon completion.

# HVAC Complete System Installation Successfully completed full residential HVAC system installation including Lennox EL297UH070 gas furnace, ML13KC1-036 condenser unit, and CK40CT-30B evaporator coil. Installed outdoor condenser unit on concrete pad with proper clearances from structure and adequate service access. Mounted air handler in basement utility area on level concrete surface with appropriate drainage provisions. Connected all refrigerant lines, electrical wiring, and condensate drainage per manufacturer specifications. Installed supply and return ductwork with proper sealing and support. Verified all safety controls, electrical connections, and gas line integrity. System tested and operational with proper airflow, refrigerant charge, and temperature differential across coil.